|
| Marsh
LCP/ML4
- Specifications
|
- BASIC SYSTEM:
Controller with Hardware.
Input Device (KID, LCP/ID, or terminal with TS-232 port).
Printhead data lines [10’ (3.05m) standard, optional
length available]
FD Series Printheads
LCP/4FP Bulk 5 Gallon (18.9 liter) or FD QuartInk System
OPERATING ENVIRONMENT:
Any normal or harsh environments with a temperature range
of 40° F (4° C) to 130o F (54.4° C)
ELECTRICAL REQUIREMENTS:
120 volts 60 hertz
110/120 volts 50/60 hertz
100 volts 50 hertz
SENSING DEVICE:
Convergent beam photocell. Retroreflective
beam photocell, or Diffuse beam photocell
available; 12 volt DC power, sinking
transistor output
MOUNTING REQUIREMENTS:
Photocell Mounting Hardware and Controller
Mounting Hardware
OPTIONS AVAILABLE:
48k Memory
Thumbwheel Switches
Mullti-tasking
shaft Encoder
CHARACTER FONTS:
64 character ASCII set
LCP/®4FP INK SYSTEMS
SYSTEM COMPONENTS:
4FP Pump Assembly (with attached power cord [6’
(1.83m)]
Mounting Hardware Kit
Ink system Cap Assembly
Ink Line Kit
ADDITIONAL COMPONETS:
5 gallon (18.9 liter) Bulk Ink
OPERATING ENVIRONMENT:
Any normal or harsh environments with a
temperature range of
40° F (4° C) to 130o F (54.4° C)
ELECTRICAL REQUIREMENTS:
110/120 volts, 50/60 hertz
220/240 volts, 50/60 hertz
INK:
Marsh LCP/FD inks
FD QUART INK SYSTEM:
System Components
FD Quart Ink Restraint
Harsh Environment Air Module
Mounting Hardware Kit
Ink System Cap Assembly
Ink Line Kit
ADDITIONAL COMPONENTS:
Quart (.946 liter) Ink Bottles
FD PRINTHEADS
PRINT HEIGHTS:
713FD Series Printhead: One line of 1/2”
(13mm) high characters, 7x5 dot matrix, or one
line of 3/8” (8.4mm) high characters, 5x5 dot
matrix
720 FD Series Printhead: One line of
3/4”
(19mm) high characters, 7x5 dot matrix, or one
line of 1/2” (13mm) high characters, 5x5 dot
matrix
1632FD Series Printhead: Two line of
1/2”
(13mm) high characters, 7x5 dot matrix, or two
line of 3/8” (8.4mm) high characters, 5x5 dot
matrix or one line of 1-1/8” (29mm) high
characters, 14x10 dot matrix
1650FD Series Printhead: Two line of
3/4”
(19mm) high characters, 7x5 dot matrix, or one
line of 1 11/16” (43mm) high characters, 14x10
dot matrix, or two line of 1/2” (23mm) high
characters, 5x5 dot matrix
APPLICATIONS:
The FD Series Printheads are suitable for both
absorbent surfaces. They are particularly
effective on very high speed conveyors and on
tough-to-mark surfaces.
INK:
Marsh LCP/FD Inks (Black, Blue, Red)
OPERATING ENVIRONMENT:
Any normal or harsh environments with a
temperature range of 40o F (4o C) to 130o F (54.4o C).
PRINTHEAD DATA LINES:
10’ (3.04m) standard length, optional lengths available
MOUNTING REQUIREMENTS:
Printhead Mounting Hardware
CONVEYOR LINE SPEEDS:
FD Printhead Maximum
Series Line Speed
713 206 ft./min. (63 m/min.)
720 328 ft./min. (100 m/min.)
1632 206 ft./min. (63 m/min.)
1650 328 ft./min. (100 m/min.)
Shaft encoder required for variable speed, stop
/ start applications, and line speeds less than
20 ft./min.
(6 m/min.).
|
|
| |
|
